Equestrian & farm electrical
Ocala is the Horse Capital of the World, and barns here deserve better than house wiring. We design and install power for barns, arenas, wells and farm buildings across Marion County and North Central Florida.
Everything a working farm runs on
A horse barn is a hard place for electrical equipment. There's dust and hay, humidity and hose-downs, rodents, and 1,200-pound animals that lean on things. We plan every barn around that: fixtures and boxes rated for the space, wiring protected where animals can reach, and circuits sized for fans running all summer.
- Barn & stall lighting
- Stall and aisle fans
- Wash racks & GFCI protection
- Tack, feed & office rooms
- Covered & open arena lighting
- Well pumps & automatic waterers
- Electric gates & openers
- Generators & transfer switches
- New services, meters & disconnects
- Underground feeders to outbuildings
- Barn apartments & living quarters
- Exterior, security & path lighting

What we see on Florida horse farms
Tripping breakers in summer
Every stall fan running at once on circuits that were never sized for it. We re-balance loads and add circuits so fans stay on in August.
No water when the power's out
A storm takes out power and the well stops. A transfer switch and generator inlet keeps the pump and waterers running safely.
Corroded boxes & fixtures
Indoor-rated parts in a humid barn rust out fast. We replace them with wet-location fixtures and sealed boxes.
Exposed or chewed wiring
Loose cable is a fire risk around hay and a hazard for horses. We run it in conduit and keep it out of reach.
Dim, uneven arena light
Shadows make riding at dusk unsafe. We lay out LED fixtures for even light across the whole ring.
Outbuildings on extension cords
Run-in sheds and shops powered by cords. We trench and install proper underground feeders and subpanels.



New barn facility, St. Johns, FL
The job: full electrical for a new red barn facility, from rough-in to the finished service.
What we did: set a new meter with two exterior disconnects feeding twin interior panels, ran every branch circuit in metal conduit on the plywood walls, hung LED high-bays across the open floor, put warm exterior lights over each door, and added emergency exit lighting.
The result: a clean, bright, code-compliant building ready for horses and equipment. See the full project →
"When we unexpectedly needed to get our generator hooked up so we could run our well and make sure our horses had water, Matt came out after hours without hesitation. He truly went above and beyond for our family."
Bring us in early
The best time to call an electrician is before the slab is poured. We can help you plan stall outlets, fan locations, wash-rack GFCIs, arena lighting and generator hookups while it's still easy and inexpensive to change.
- We'll review your barn plans and quote from them
- We coordinate with your barn builder's schedule
- We handle permits, inspections and the utility
Get a farm quote
Tell us about the job and we'll call you back, usually the same day.
Request sent
Thanks! We'll be in touch shortly. Need us sooner? Give us a call.
Proud to work in the Horse Capital of the World
A few of the equestrian organizations and venues that make Marion County and North Central Florida what it is.
Barn wiring questions
Do barns need special wiring?
Barns are treated as damp, dusty and sometimes wet locations, and many have animals present. That changes which boxes, fixtures and wiring methods are appropriate, and where GFCI protection is needed. We'll design to the code requirements for your building and how you use it.
How much power does a horse barn need?
It depends on stall count, fans, lighting, wash racks, any living quarters and equipment like welders or dryers. Many barns need their own service or a large subpanel. Our guide How much power does a horse barn need? walks through it.
Can you power my well and waterers during an outage?
Yes. We install transfer switches and generator inlets sized for your pump and essentials. See our generator guide.
Do you work with barn builders?
Yes. We regularly work alongside pole-barn and steel-building crews and fit our rough-in and trim into their schedule.
